Kicker Stereo Amplifier ZX3502 User Manual

ZX  
STEREOAMPLIFIER  
ZX350.2, ZX450.2, ZX550.2, ZX850.2  
©2007 Stillwater Designs  
 
Operation  
RED Badge Light off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt  
power terminal (should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V)  
3) Check for reversed power and ground connections. 4) Ground terminal, for proper conductivity. 5)  
Check for blown fuses.  
L
R
R
AUTO  
INPUT  
LEVEL  
L
TURN ON  
XOVER  
DC AUDIO  
OFFSET  
+12V  
OFF HI LO  
LO  
HI  
INPUT  
OUTPUT  
RED Badge Light on, no output? Check the following: 1) RCA connections 2) Test speaker  
outputs with a “known” good speaker. 3) Substitute source unit with a “known” good source unit. 4)  
Check for a signal in the RCA cable feeding the amplifier with the VOM meter set to measure “AC”  
voltage.  
REMOTE BASS  
SPKR +  
SPKR -  
SPKR+  
SPKR -  
End Panel LED flashing with loud music? The yellow LED indicates low battery voltage. Check  
all the connections in your vehicles charging system. It may be necessary to replace or charge your  
vehicles battery or replace your vehicles alternator.  
1. Automatic Turn-On Selection The ZX series offers three different automatic turn-on modes that can  
be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode  
causes the REM terminal to have +12V out for turning on additional amplifiers.  
End Panel LED on, no output? 1) Amplifier is very hot. Thermal protection is engaged. Test  
for proper impedance at the speaker terminals with a VOM meter (see the diagrams in this manual  
for minimum recommended impedance and multiple speaker wiring suggestions). Also check for  
adequate airflow around the amplifier. 2) Amplifier shuts down only while vehicle is running. Voltage  
protection circuitry is engaged. Voltage to the amplifier is not within the 9-16 volt operating range. Have  
the vehicle's charging and electrical system inspected. 3) Amplifier will only play at low volume levels.  
Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle  
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended  
impedance.  
Remote Turn-On Set the switch to +12V to use the remote turn-on lead from your source unit. Run  
18 Ga wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the  
amplifiers positive and negative power terminals. This is the preferred automatic turn-on method.  
DC Offset Turn-On If Remote Turn-On is not an option, the next best setting is DC Offset. The DC  
Offset mode detects a 6 volt surge from the HI Level speaker outputs when the source unit has been  
turned on.  
Signal Sense Turn-On The Audio setting is the final alternative for Automatic turn-on. This is a Signal  
Sense turn-on method that detects the incoming audio signal from your source unit and automatically  
turns on the amp. This turn-on method will not work properly if the input gain control is not set  
appropriately.  
No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or  
speaker input) and speaker output connections for the channel 3) Swap the RCA (or speaker input)  
cable from left to right. If the problem changes sides then you have a bad RCA (or speaker input) cable  
or source unit problem. 4) Swap the speaker output wire from left to right. If the problem changes sides  
then you have a bad speaker cable, passive crossover network and/or speaker.  
2. Input Level The RCA inputs on Kicker ZX amplifiers are capable of receiving either Hi or Low-level  
signals from your source unit. If the only output available from your source unit is a Hi-Level signal, simply  
press in the Input Level switch on the amplifier. Refer to the wiring section of this manual for additional  
instructions.  
Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker  
input) cable 2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper  
grounding 4) Check the gain settings and turn them down if they are set too high.  
3. Crossover Switch Use the XOVER switch on the end panel of the amplifier to set the internal  
crossover to OFF, HI or LO. When the switch is set to OFF, a full bandwidth signal will be amplified.  
Set the switch to HI if you want the amplifiers internal crossover to serve as a high-pass filter. Set the  
switch to LO if you want the amplifiers internal crossover to serve as a low-pass filter. Never change the  
crossover “OFF/HI/LO” switch setting with the audio system on!  
Poor stereo image or reduced bass response? Check system phasing by turning the balance  
control from left to right. If there is more bass output when turned to either side, then check your speaker  
wiring, passive crossover networks and speaker terminals for proper positive and negative connections.  
Reverse a speaker connection from positive to negative on the stereo/subwoofer channel(s); if the bass  
improves, the speaker was out of phase.  
4. Input Gain Control The input gain control is not a volume control. It matches the output of the  
source unit to the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source  
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can hear  
audible distortion, then turn it down a little.  
Ground Noise? Kicker amplifiers are engineered to be fully compatible with all manufacturers’ head  
units. Some head units may require additional grounding to prevent noise from entering the audio signal.  
If you are experiencing this problem with your head unit, in most cases running a ground wire from the  
RCA outputs on the head unit to the chassis will remedy this issue.  
5. Bass Boost Control The variable bass boost control on the top of the amplifier is designed to give  
you increased output 0 - 18dB at 40 Hz. The setting for this control is subjective. If you turn it up, you  
must go back and adjust the input gain control to avoid clipping the amplifier.  
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The Kicker  
Coaxial and Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with  
any amplifier designed to operate at a four ohm load. If you want to use two Kicker Coaxial or Component speakers on  
a single channel of your amplifier wire the speakers in series. This will improve the sound quality, lower the total harmonic  
distortion and lessen the thermal load at the amplifier. This may prevent an amplifier from shutting down, due to over-  
current protection circuitry.  
6. Crossover Control The variable crossover on the top of the amplifier allows you to adjust the  
crossover frequency from 50-200Hz. The setting for this control is subjective; 80Hz is a good place to  
start.  
Mount the metal bracket  
7. RemoteBass(Level Control) When the crossover  
on your ZX.2 series amplifier is set to LO pass, you  
have the ability to control the output level of the  
Back View  
Side View  
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper  
connections can result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.  
amplifier remotely. To mount the remote bass level  
control, simply screw the metal bracket to the chosen  
R
location. Then slide the housing onto the bracket until  
it snaps into place. Run the cable from the controller  
to the “Remote Bass” jack on the amplifier chassis.  
Slide the housing until it snaps into the metal bracket  
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER  
Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker  
download or view the corresponding information. Please E-mail support@kicker.com or call Technical Services (405) 624-  
8583 for unanswered or specific questions.  
L
R
L
AUTO  
INPUT  
LEVEL  
TURN ON  
XOVER  
+12V DC AUDIO  
OFFSET  
OFF HI LO  
LO  
HI  
INPUT  
OUTPUT  
REMOTE BASS  
SPKR  
+
SPKR  
-
SPKR+  
SPKR  
-
4 Conductor  
Phone Cable  
TroubleShooting  
Model ZX350.2  
Model ZX550.2  
110 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)  
Signal to Noise Ratio -94  
CEA-2006 (ref: 1W, A-weighted)  
205 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)  
Signal to Noise Ratio -91  
CEA-2006 (ref: 1W, A-weighted)  
If your amplifier does not appear to be working, check the obvious things first such as blown fuses,  
poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There  
is an illuminated red badge on top of the amplifier denoting the power state of the amp in addition to  
the Protection LED on the end panel of your Kicker ZX series amplifier. When the red badge is lit this  
indicates the amplifier is turned on and the amplifier is functioning properly.  
Model ZX450.2  
150 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)  
Signal to Noise Ratio -91  
Model ZX850.2  
295 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)  
Signal to Noise Ratio -89  
CEA-2006 (ref: 1W, A-weighted)  
CEA-2006 (ref: 1W, A-weighted)  
 
ZX.2AMPLIFIER  
4
5
InternationalWarranty  
ElectronicsLimitedWarranty  
Contact your International Kicker dealer or distributor concerning specific procedures for your countrys warranty policies.  
Kicker warrants this product to be free from defects in material and workmanship under normal use for a period of  
THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is  
warranted for TWO (2) YEARS from date of original purchase with receipt. In all cases you must have the original receipt.  
Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction during the  
warranty period, Kicker will repair or replace (at its discretion) the defective merchandise with equivalent merchandise at  
no charge. Warranty replacements may have cosmetic scratches and blemishes. Discontinued products may be replaced  
with more current equivalent products.  
WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning  
up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at  
the same volume level. The threshold of pain is always an indicator that the sound level is too loud and may permanently  
damage your hearing. Please use common sense when controlling volume.  
GARANTÍA INTERNACIONAL  
VersiónEspañol  
This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to  
the original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty  
as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or  
implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties; therefore these  
exclusions may not apply to you. This warranty gives you specific legal rights; however you may have other rights that  
vary from state to state.  
Comuníquese con su concesionario o distribuidor Kicker internacional para obtener infor ación sobre procedimientos  
específicos relacionados con las normas de garantía de su país.  
ADVERTENCIA: Los excitadores Kicker son capaces de producir niveles de sonido que pueden dañar permanentemente  
el oído. Subir el volumen del sistema hasta un nivel que produzca distorsión es más dañino para el oído que escuchar un  
sistema sin distorsión al mismo volumen. El dolor es siempre una indicación de que el sonido es muy fuerte y que puede  
dañar permanentemente el oído. Sea precavido cuando controle el volumen.  
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE  
Defective merchandise should be returned to your local Authorized Stillwater Designs (Kicker) Dealer for warranty  
Designs directly. You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.  
La frase “combustible para vivir la vida Livin’ Loud™ a todo volumen” se refiere al entusiasmo por la vida que la marca  
Kicker de estéreos de automóvil representa y a la recomendación a nuestros clientes de que vivan lo mejor posible (“a  
todo volumen”) en todo sentido. La línea de altavoces y amplificadores Kicker es la mejor del mercado de audio de  
automóviles y por lo tanto representa el “combustible” para vivir a todo volumen en el área de “estéreos de automóvil” de  
la vida de nuestros clientes. Recomendamos a todos nuestros clientes que obedezcan todas las reglas y reglamentos  
locales sobre ruido en cuanto a los niveles legales y apropiados de audición fuera del vehículo.  
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (Kicker), call the Kicker  
Customer Service Department at (405) 624-8510 for a Return Merchandise Authorization (RMA) number. Package all  
defective items in the original container or in a package that will prevent shipping damage, and return to:  
INTERNATIONALE GARANTIE  
DeutscheVersion  
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075  
Nehmen Sie mit Ihren internationalen Kicker-Fachhändler oder Vertrieb Kontakt auf, um Details über die Garantieleistungen  
in Ihrem Land zu erfahren.  
The RMA number must be clearly marked on the outside of the package. Please return-only defective components. The  
return of functioning items increases your return freight charges. Non-defective items will be returned freight-collect to  
you.  
WARNUNG: KICKER-Treiber können einen Schallpegel erzeugen, der zu permanenten Gehörschäden führen kann!  
Wenn Sie ein System auf einen Pegel stellen, der hörbare Verzerrungen erzeugt, schadet das Ihren Ohren mehr, als ein  
nicht verzerrtes System auf dem gleichen Lautstärkepegel. Die Schmerzschwelle ist immer eine Anzeige dafür, dass der  
Schallpegel zu laut ist und zu permanenten Gehörschäden führen kann. Seien Sie bei der Lautstärkeeinstellung bitte  
vernünftig!  
Include a copy of the original receipt with the purchase date clearly visible, and a “proof-of-purchase” statement listing  
the Customers name, Dealers name and invoice number, and product purchased. Warranty expiration on items without  
proof-of-purchase will be determined from the type of sale and manufacturing date code. Freight must be prepaid;  
items sent freight-collect, or COD, will be refused.  
Der Slogan “Treibstoff für Livin’ Loud” bezieht sich auf die mit den Kicker-Autostereosystemen assoziierte Lebensfreude  
und die Tatsache, dass wir unsere Kunden ermutigen, in allen Aspekten ihres Lebens nach dem Besten (“Livin’ Loud”) zu  
streben. Die Lautsprecher und Verstärker von Kicker sind auf dem Markt für Auto-Soundsysteme führend und stellen somit  
den “Treibstoff” für das Autostereoerlebnis unserer Kunden dar. Wir empfehlen allen unseren Kunden, sich bezüglich der  
zugelassenen und passenden Lautstärkepegel außerhalb des Autos an die örtlichen Lärmvorschriften zu halten.  
WHAT IS NOT COVERED?  
This warranty is valid only if the product is used for the purpose for which it was designed.  
It does not cover:  
o Damage due to improper installation  
o Subsequent damage to other components  
GARANTIE INTERNATIONALE  
VersionFrançaise  
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation  
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be considered  
abuse  
Pour connaître les procédures propres à la politique de garantie de votre pays, contactez votre revendeur ou distributeur  
International Kicker.  
o Any cost or expense related to the removal or reinstallation of product  
o Speakers damaged due to amplifier clipping or distortion  
o Items previously repaired or modified by any unauthorized repair facility  
o Return shipping on non-defective items  
o Products with tampered or missing barcode labels  
o Products returned without a Return Merchandise Authorization (RMA) number  
o Freight Damage  
AVERTISSEMENT: Les haut-parleurs Kicker ont la capacité de produire des niveaux sonores pouvant endommager  
l’ouïe de façon irréversible ! Laugmentation du volume d’un système jusqu’à un niveau présentant une distorsion audible  
endommage davantage l’ouïe que l’écoute d’un système sans distorsion au même volume. Le seuil de la douleur est  
toujours le signe que le niveau sonore est trop élevé et risque d’endommager l’ouïe de façon irréversible. Réglez le volume  
en faisant prevue de bon sens !  
o The cost of shipping product to Kicker  
o Service performed by anyone other than Kicker  
Lexpression “ carburant pour vivre plein pot “ fait référence au dynamisme de la marque Kicker d’équipements audio  
pour véhicules et a pour but d’encourager nos clients à faire le maximum (“ vivre plein pot “) dans tous les aspects de leur  
vie. Les haut-parleurs et amplificateurs Kicker sont les meilleurs dans le domaine des équipements audio et représentent  
donc pour nos client le “ carburant pour vivre plein pot “ dans l’aspect “ installation audio de véhicule “ de leur vie.  
Nous encourageons tous nos clients à respecter toutes les lois et réglementations locales relatives aux niveaux sonores  
acceptables à l’extérieur des véhicules.  
HOW LONG WILL IT TAKE?  
Kicker strives to maintain a goal of 72-hour service for all electronics (amplifiers, crossovers, equalizers, etc.) returns.  
Delays may be incurred if lack of replacement inventory or parts is encountered.  
Failure to follow these steps may void your warranty. Any questions can be directed to the Kicker Customer Service  
Department at (405) 624-8510.  
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • (405) 624-8510  
10262007-D+08ZX.2  
 
ZX.2AMPLIFIER  
6
7

Intel Computer Hardware AXXRAKSAS2 User Manual
Inter Tel Answering Machine 8622 User Manual
JBL Speaker EON PowerSub G2 User Manual
JVC CRT Television GGT0116 001B H User Manual
JVC Flat Panel Television 0807TNH II IM User Manual
JVC Portable CD Player XL PG59SL User Manual
Kenmore Refrigerator 241858201 User Manual
Kenwood Blender HB790 series User Manual
Kenwood Stereo Amplifier KAC 9104D User Manual
KitchenAid Washer KAWE850V User Manual