15” LCD TV
OWNER'S MANUAL
SAFETY PRECAUTIONS
WARNING: TO REDUCE THE RISK OF ELECTRIC
CAUTION
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE. DO NOT PLACE OBJECTS
FILLED WITH LIQUIDS ON OR NEAR THIS
UNIT.
RISQUE DE CHOC ÉLECTRIQUE NE
PAS OUVRIR
AVIS
* SEE REAR OF UNIT FOR GRAPHIC SYMBOLS *
The lightning flash with an arrowhead within a
triangle alerts you to uninsulated dangerous
voltage within the product's enclosure that could
cause an electric shock.
CAUTION: DANGER OF EXPLOSION IF
BATTERY IS INCORRECTLY REPLACED. REPLACE
ONLY WITH THE SAME OR EQUIVALENT TYPE.
The exclamation point within a triangle alerts
you to the presence of important operating,
maintenance and servicing instructions in this
user’s manual.
The symbol for Class II
(Doublelnsulation)
PLACEMENT INFORMATION
• Do not use this unit in places that are extremely hot, cold, dusty, or humid.
• Do not restrict the airflow of this unit by placing it somewhere with poor airflow, by covering
it with a cloth, or by placing it on bedding or carpeting.
SAFETY INFORMATION
• When connecting or disconnecting the AC cord, grip the plug and not the cord itself. Pulling
the cord may damage it and create a hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC cord.
CONDENSATIONINFORMATION
• When left in a heated room where it is warm and damp, water droplets or condensation may
form inside the unit. When there is condensation inside the unit, the unit may not function
normally. Let the unit stand for 1-2 hours before turning the power on or gradually heat the
room and let the unit dry before use.
FCC INFORMATION
WARNING: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could avoid the user authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Shielded cables must be used with this unit to ensure compliance with the Class FCC limits.
WARNING: Should any problems occur, disconnect the AC cord and refer servicing to
a qualified technician.
2
PLV1615CS1- E2-23 JENSEN-DC.pmd
2
06/08/2007, 17:56
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
13. Unplug this apparatus during
lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such as
power-supply cord or plug is
damaged, liquid has been spilled or
objectshavefallenintotheapparatus,
the apparatus has been exposed to
rain or moisture, does not operate
normally, or has been dropped.
9. Do not defeat the safety purpose of
the polarized or grounding-type
plug. A polarized plug has two blades
with one wider than the other. A
grounding type plug has two blades
and a third grounding prong. The
wide blade or the third prong are
provided for your safety. If the
provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly
at
the
plug,
convenience
receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart,
stand, tripod, bracket,
or table specified by the
manufacturer, or sold
with the apparatus.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from
tip-over.
3
PLV1615CS1- E2-23 JENSEN-DC.pmd
3
06/08/2007, 17:56
TABLE OF CONTENTS
SAFETY PRECAUTIONS ...................................................................................... 2
IMPORTANT SAFETY INSTRUCTIONS ............................................................... 3
REMOTE CONTROL ........................................................................................... 5
ACCESSORIES ..................................................................................................... 5
REMOTE CONTROL REFERENCE GUIDE .......................................................... 6
UNIT REFERENCE GUIDE ................................................................................. 7
CONNECTIONS ......................................................................................... 8 – 13
Connecting a TV Antenna/Cable/Satellite ......................................................... 8
Connecting an A/V Device (VCR, PVR Camcorder, Game System, etc.) ... 9 – 11
Connecting a High-Definition (HD) Source ................................................... 12
Connecting a PC ............................................................................................. 12
Connecting an Audio Amplifier ........................................................................ 13
Connecting the Power Cord ............................................................................. 13
INSTALLATION .................................................................................................... 14
Removing the Base Stand ............................................................................... 14
Mounting on the Wall ..................................................................................... 14
USING HEADPHONES .................................................................................... 15
UNIT OPERATION ............................................................................................ 15
Turning the Unit on for the First Time .............................................................. 15
TV SETUP .................................................................................................. 16 – 21
Video Menu .................................................................................................... 16
VGA Settings in PC Mode .............................................................................. 17
Audio Menu .................................................................................................... 17
TV Menu ......................................................................................................... 18
Setup Menu ............................................................................................. 18 – 20
Time Setup Setting ......................................................................................... 19
Caption Setting .............................................................................................. 20
Restore Setting ............................................................................................... 20
Parental Menu .......................................................................................... 20 – 21
Password ....................................................................................................... 20
Parental Control Setting .................................................................................. 21
TROUBLE SHOOTING GUIDE ........................................................................ 22
4
PLV1615CS1- E2-23 JENSEN-DC.pmd
4
06/08/2007, 17:56
REMOTE CONTROL
USING THE REMOTE CONTROL
•
•
Point the remote control at the REMOTE SENSOR located on the unit.
When using this unit in very bright light, the infrared REMOTE CONTROL SENSOR may not
work properly.
•
The recommended effective distance for using the remote control is about 16 feet (5 meters).
TO CHANGE THE REMOTE CONTROL BATTERY
1. Open the battery door.
2. Insert two “AAA” batteries.
BATTERY REPLACEMENT
When the batteries become weak, the operating distance of the remote control will be greatly
reduced and you will need to replace the batteries.
Note: • If the Remote Control is not going to be used for a long time, remove the batteries to
avoid damage caused by battery leakage corrosion.
• Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or
rechargeable (NICKEL-CADMIUM) batteries.
WARNING: Do not dispose of batteries in a fire or they may leak and/or explode.
Many universal remote controls have a “learning” feature, we recommend you use that feature
to program the remote control.
For any questions or problems related to programming a universal remote control, you must
contact the customer service department of the universal remote control manufacturer for
assistance, or refer to the instructions included with the universal remote control. We cannot
offer assistance in programming universal remote controls.
ACCESSORIES
PLEASE LOCATE THE INCLUDED ACCESSORIES.
Remote control (with battery) .............................................................................. x 1
AC adapter ....................................................................................................... x 1
Car power adapter ............................................................................................. x 1
Audio/Video cable ............................................................................................. x 1
Mounting screw ............................................................................................... x 4
Specifications and appearance are subject to change without notice.
5
PLV1615CS1- E2-23 JENSEN-DC-R1.pmd
5
11/7/2007, 9:37 AM
REMOTE CONTROL REFERENCE GUIDE
4) PICTURE Button
Press to select from preset screen display
settings to match the type of show you
are watching (Standard, Dynamic,
Personal, Soft & Movie)
5) DISPLAY Button
Press to change disc status information
displayed on the screen.
6) CURSOR (
,
,
,
) Buttons
Press to highlight selections on a menu
screen and adjust certain settings.
CH+/CH– Button
Press CH+/CH– to change the TV
channels.
VOLUME (–/+) Buttons
Press to adjust the volume level.
7) TV Button
Press to select TV mode.
8) CC Button
Press to activate the Closed Captioning
feature. This function only works on
programs broadcast with captions.
9) EXIT Button
Press to return to previous menu or exit
the menu and return directly to normal
viewing.
10) STANDBY Button
Press to turn ON the unit or put it in
STANDBY (OFF) mode.
11) MUTE Button
Press to mute the sound. Press again to
cancel mute.
12) FUNCTION Button
Press to switch between TV / AV IN / YUV
IN / PC IN.
13) SOUND Button
Press to select from preset sound settings
(Personal, Standard, Voice, Music,
Theater) to match the type of show you
are watching.
1) SLEEP Button
Press to set the SLEEP timer. The unit will
14) ENTER Button
remain on for the time that is set, and
will automatically shut off afterwards.
2) Number (0 - 9 and dot) Buttons
In DVD mode, use when creating programs
and locating a title/chapter or specific
time.
Press to confirm selections on a menu
screen.
15) MENU Button
Press to display the on-screen menu.
16) AV Button
Press to select AV IN mode.
17) MTS Button
InTV and other modes, use when inputting
TV channel number and entering a parental
control password.
Press to select MONO sound, STEREO
sound and Secondary Audio Program
(SAP).
3) LAST CH Button
Press to switch repeatedly between the
last two channels displayed.
18) FORMAT Button
Press to select the picture format.
6
PLV1615CS1- E2-23 JENSEN-DC.pmd
6
06/08/2007, 17:56
UNIT REFERENCE GUIDE
3
4
17
5
6
8 9
7
10
1314
11 12
15
16
1) Color LCD Screen
2) STANDBY/ON Button
4) Removable Base Stand
5) DC IN 12V
6) AV OUT Video Output Jack
7) AV OUT Audio Output Jacks
(Left/Right)
Turns the unit on and off.
MENU Button
Enters and exits the TV menu.
FUNCTION Button
8) AV IN Video Input Jack
9) AV IN Audio Input Jacks (Left/Right)
10) PC IN MONITOR/VGA Jack
11) PC IN Audio Jack
12) YUV IN Component Video Input Jacks
(Y/PB/PR)
13) YUV IN Audio Input Jacks (Left/Right)
14) AV IN S-Video Input Jack
15) Headphone Jack
Selects TV, AV IN, YUV IN or PC IN.
– VOL + Controls
Adjusts the volume level and highlight
selections (Left & Right) on the menu
screen.
/
Buttons
Selects a TV channel and highlight
selections (Up & Down) on the menu
screen.
3) STANDBY Indicator
Indicates whether the unit is ON or in
STANDBY (OFF) mode.
16) TV Antenna Cable Terminal - Coaxial
TV Antenna Input
Light On: The unit is in STANDBY.
Light Off: The unit is turned ON.
17) Remote Control Sensor
Do not block this sensor or remote
control will not work.
7
PLV1615CS1- E2-23 JENSEN-DC.pmd
7
06/08/2007, 17:56
CONNECTIONS
CONNECTING A TV ANTENNA/CABLE/SATELLITE
To view television channels correctly, a signal
must be received from one of the following sources:
- An indoor or outdoor aerial antenna
- A cable system
- A satellite system
Connecting a Digital Antenna
The tuner in this TV receives ATSC TV signals from
an antenna.
This digital TV can receive standard (SDTV) and
high definition (HDTV) over the air broadcasts.
Satellite, Cable, or
TV antenna cable to
TV ANTENNA CABLETerminal
(cable not included)
Connecting an Analog Antenna or Device
The tuner in this TV can receive NTSC TV signals, analog cable signals or the RF output from
a satellite receiver, VCR or cable box.
CONNECTING ANAUDIO AMPLIFIER
This connection allows you to use an audio amplifier and external speakers.
Connect the right (red) and left (white) audio
OUTPUT from this unit to the right (red) and left
(white) audio INPUT on your amplifier. Refer to
your amplifier’s user manual for more information.
Note:
To control the audio, both the TV and the amplifier
must be turned on, and the volume of the amplifier
must be set above 0, or you will not hear any
sound.
If you want to hear the sound from the amplifier
only, press the VOL – button on the TV to decrease
the volume or press the MUTE button on the remote
control to turn off the sound.
8
PLV1615CS1- E2-23 JENSEN-DC.pmd
8
06/08/2007, 17:57
CONNECTIONS
CONNECTINGTOA/V DEVICES (VCR, PVR, Camcorder, Game System, etc.)
Connecting to Devices with an S-Video Output
To connect to A/V devices such as a VCR or camcorder:
- Connect to a VCR
Connect the right (red) and left (white) audio output
from the VCR to the right (red) and left (white)
input on this unit (Audio cable not included).
Connect the S-VIDEO output from the VCR to the
S-VIDEO input on this unit (S-VIDEO cable not
included).
Make sure you connect both audio and video from
the same VCR to the same input (AV IN).
Note:
Please refer to the user manual for the VCR for
more information.
- Connect to a camcorder
Connect the right (red) and left (white) audio output
from the camcorder to the right (red) and left (white)
input on this unit (Audio cable not included).
Connect the S-VIDEO output from the camcorder to
the S-VIDEO input on this unit (S-VIDEO cable not
included).
Make sure you connect both audio and video from
the same camcorder to the same input (AV IN).
Note:
Please refer to the user manual for the camcorder
for more information.
9
PLV1615CS1- E2-23 JENSEN-DC.pmd
9
06/08/2007, 17:57
CONNECTIONS
Connecting to Devices with a Composite (yellow RCA-type) Video Output
To connect to A/V devices such as a VCR or camcorder:
- Connect to a VCR
Connect the right (red) and left (white) audio output
from the VCR to the right (red) and left (white) input
on this unit.
Connect the video (yellow) output from the VCR to
the video input on this unit.
Make sure you connect both audio and video from
the same VCR to the same input (AV IN).
Note:
Please refer to the user manual for the VCR for
more information.
AUDIO/VIDEO CABLE [included]
- Connect to a camcorder
Connect the right (red) and left (white) audio output
from the camcorder to the right (red) and left (white)
input on this unit.
Connect the video (yellow) output from the camcorder
to the video input on this unit.
Make sure you connect both audio and video from
the same camcorder to the same input (AV IN).
Note:
Please refer to the user manual for the camcorder for
more information.
AUDIO/VIDEO CABLE [included]
10
PLV1615CS1- E2-23 JENSEN-DC-R1.pmd
10
11/7/2007, 9:33 AM
CONNECTIONS
Connecting to Devices with a Composite (yellow RCA-type) Video Input
To connect to A/V devices such as a VCR, PVR or camcorder:
- Connect to a VCR/PVR
Connect the right (red) and left (white) audio input
from the VCR/PVR to the right (red) and left (white)
output on this unit.
Connect the video (yellow) input from the VCR/
PVR to the video output on this unit.
Make sure you connect both audio and video from
the same VCR/PVR to the same output (AV OUT).
Note:
Please refer to the user manual for the VCR/PVR
for more information.
Note:
• After connection, please operate inTV/AV mode.
• For the reason of copyright protection, the result
copy may has bad picture and/or sound.
AUDIO/VIDEO CABLE [included]
- Connect to a camcorder
Connect the right (red) and left (white) audio input
from the camcorder to the right (red) and left (white)
output on this unit.
Connect the video (yellow) input from the camcorder
to the video output on this unit.
Make sure you connect both audio and video from
the same camcorder to the same output (AV OUT).
Note:
Please refer to the user manual for the camcorder
for more information.
Note:
• After connection, please operate in TV/AV mode.
• For the reason of copyright protection, the result
copy may has bad picture and/or sound.
AUDIO/VIDEO CABLE [included]
11
PLV1615CS1- E2-23 JENSEN-DC-R1.pmd
11
11/7/2007, 9:34 AM
CONNECTIONS
CONNECTING A HIGH-DEFINITION (HD) SOURCE
High-Definition (HD) Devices with component video output must be connected to the YUV
input.
Connect the three video outputs (Y, Pb, Pr) from the source to the corresponding video inputs on
this unit (Component video cable not included).
Connect the right (red) and left (white) audio output from the source to the right (red) and left
(white) input on this unit (Audio cable not included).
Make sure you connect both audio and video from the same source to YUV IN.
Note: When connecting a DVD player to the
television, the picture resolution is solely
dependent upon the resolution supported by the
DVD player attached. DVD Player resolutions vary
from 480i to 1080i, and this television can support
DVD players up to a maximum resolution of 1080i.
HD SOURCE
with component video output
(Digital Cable Box*, Satellite Receiver*, or
external over-the-air HD-Tuner)
*
May
require
a
subscription for receiving
HD channels, check with
your
cable/satellite
service provider for
details.
CONNECTING A PC
Connect the 15-pin D-SUB PC/VGA connector from
your computer to the 15-pin D-SUB PC/VGA input
on this unit using a monitor cable (not included).
Connect a stereo audio cable (not included) to
the PC AUDIO IN jack on this unit, and the other
end to the AUDIO OUT jack on your computer’s
sound card.
12
PLV1615CS1- E2-23 JENSEN-DC.pmd
12
06/08/2007, 17:57
POWER SUPPLY
USINGTHE CAR POWERADAPTER
The included car power adapter allows the unit to be used with vehicles that have a 12V,
negative ground electrical system.
Cautions:
• Use the provided car power adapter only. Use with other car
power adapters could damage the unit.
• The car power adapter included with this unit is for its use
only. Do not use it with other equipment.
• In the interest of traffic safety, do not operate this unit or
view videos while driving a vehicle.
• Make sure the unit is securely fastened to prevent it from
falling or flying through the air in the event of an accident.
• When the inside of the cigarette lighter socket is dirty with
ashes or dust, the plug section may become hot due to poor
contact. Be sure to clean the cigarette lighter socket before
use.
• After use, disconnect the car power adapter from both the
unit and cigarette lighter socket.
USINGTHE AC POWER ADAPTER
The supplied AC adapter operates on AC 120V.
• Press the STANDBY/ON button on the unit or remote control
to turn on the unit.
Note:
• The AC adaptor included with this unit is for its use only. Do
not use it with other equipment.
• Be sure the AC power cord is disconnected and all functions are
off before making connections.
• Make sure that all the components are connected correctly.
• To prevent electrical shock, match wide blade of plug to wide
slot of wall outlet, then fully insert.
• When you are not going to use the unit for a long period of time,
disconnect the power cord.
13
PLV1615CS1- E2-23 JENSEN-DC.pmd
13
06/08/2007, 17:57
INSTALLATION
REMOVINGTHE BASE STAND
WARNING: The LCD display is very fragile, and must be protected at all times when removing
the base stand. Be sure that no hard or sharp, or anything that could scratch or damage the LCD
display, come in contact with it. Do NOT place pressure on the front of the unit at any time
because the screen could crack.
1. Disconnect any cables or cords connected to the unit.
2. Lay the unit down on a flat surface, so the backside is facing up, making sure to place a soft
cushioned material (such as a pillow or thick piece of foam) beneath the screen.
3. Remove the four screws and then remove the BASE STAND from the unit.
MOUNTING ONTHEWALL
This unit is VESA-compliant, and is designed to be wall-mounted with a VESA-compliant 3” x 3”
(75mm x 75mm) mounting kit designed for flat-panel TVs (sold separately). Mount this unit
according to the directions included with the mounting kit.
Note: You must remove the base stand before mounting the unit on the wall.
Four mounting holes
(mounting screw x4
included)
14
PLV1615CS1- E2-23 JENSEN-DC-R1.pmd
14
11/2/2007, 5:27 PM
USING HEADPHONES
• Turn down the volume before connecting headphones to the unit, then adjust the volume to
your desired level.
• When headphones are connected, no sound will come from the front speakers.
Note:
• Avoid listening to sound at high levels for prolonged periods of time. This may be harmful to
you and may cause hearing loss.
Earphones / Headphones
(1/8” [3.5mm] diameter plug)
UNIT OPERATION
TURNING THE UNIT ON FORTHE FIRSTTIME
The first time for you turning on the unit, the unit will enter Virgin mode. You can easily follow
up prompt message on screen to finish basic settings of the system.
1. Press the ENTER button to proceed the Initial Setup.
2. Use the
3. Use the
/
/
button to select your OSD language, and press the button to the next step.
button to select your TV tuner source (Antenna or Cable), and press the
button to the next step.
4. Make sure RF aerial has been connected properly to TV ANTENNA input jack on the rear of
the system, press the ENTER or
button. The system will automatically start to scan and
preset all available TV channels.
5. After scaning finished, “Inital setup is Complete.” will appear on the screen. Press the
ENTER button to finish Initial Setup.
After finishing above settings, the system will return to the first TV channel scaned just now.
Note: When the unit is not going to be used for a long time, disconnect the AC power cord from
AC power outlet.
15
PLV1615CS1- E2-23 JENSEN-DC.pmd
15
06/08/2007, 17:57
TV SETUP
VIDEO MENU
1. Press the MENU button.
2. Press the ENTER or
button to select Video.
3. Use the
or
button to select the options (Picture Mode, Brightness, Contrast, Saturation,
Tint, Sharpness or Color Temperature). Adjust them using the
will change to your desired setting); or press the ENTER or
settings.
or
button (The screen
button to go into the detailed
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
TV MODE AV / YUV MODE
Video
Picture Mode
Brightness
Contrast
Personal
Video
Audio
Picture Mode
Personal
50
50
50
0
Brightness
Contrast
50
50
50
0
Audio
Setup
Parental
Saturation
Tint
Saturation
Tint
TV
Setup
Sharpness
ColorTemperature
4
Sharpness
ColorTemperature
4
Standard
Standard
Parental
Video
Video
Select EXIT Exit
Select EXIT Exit
PC MODE
Video
Picture Mode
Personal
Brightness
50
50
Audio
Setup
Parental
Contrast
VGA
ColorTemperature
Standard
Video
Select EXIT Exit
• Picture Mode
: Select from preset screen display settings to match the type of show you
are watching (Standard, Dynamic, Personal, Soft & Movie). (Select
Personal mode to recall your customed settings on brightness, contrast,
saturation, tint, sharpness and color temperature.)
• Brightness
• Contrast
: Adjust the brightness of the picture. Brighten or darken the whole
picture.
: Adjust to sharpen the picture quality. The black portions of the picture
become richer in darkness and the white become brighter.
: Adjust the color saturation of the picture.
• Saturation
• Tint
• Sharpness
: Adjust the tint of the picture. (Toward purple / Toward green)
: Adjust the sharpness level to improve detail in the picture.
• Color Temperature : Adjust the three color temperature of the picture. Choose from Standard
(balanced), Warm (red white), or Cool (blue white) modes.
16
PLV1615CS1- E2-23 JENSEN-DC.pmd
16
06/08/2007, 17:57
TV SETUP
VGA Settings in PC Mode
Use the
or
button to select the options (Auto Adjust, H. Position, V. Position, Phase or
Clock). Adjust them using the or button. The screen will change to your desired setting.
(Press the ENTER or button to confirm Auto Adjust.)
-
-
Resolution : 1,024 x 768 max
Refresh Frequency : 60Hz max
Video
Auto Adjust
H. Position
V. Position
50
50
Audio
Setup
Parental
•
•
•
H. Position : Center the image by moving it
left or right.
V. Position : Center the image by moving it
up or down.
Phase
Clock
3
127
Phase
: Adjusts the image if there is
flicker of screen letters, color
misalignment, or blurring.
VGA
ENTER Enter
Select EXIT Return
•
Clock
: Adjusts the display clock to
change width of the image.
AUDIO MENU
1. Press the MENU button.
2. Use the
or
button to select Audio, then press the ENTER or
button to go into the
Audio settings.
3. Use the
or
button to select the options (Balance, Bass, Treble or Audio Mode). Adjust
or button (The screen will change to your desired setting); or press the
them using the
ENTER or
button to go into the detailed settings.
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
TV MODE
AV / YUV / PC MODE
0
0
0
0
Video
Balance
Bass
Video
Audio
Balance
Bass
Audio
Setup
Parental
Treble
50
Treble
50
Audio Mode
Audio Mode
Off
Off
TV
Setup
Parental
Audio
Select EXIT Exit
Audio
Select EXIT Exit
Note: Experiment with different sound settings until you find the settings you prefer.
• Balance
• Bass
• Treble
: Adjust the balance level toward the left or right speakers.
: Adjust the bass range.
: Adjust the treble range.
• Audio Mode : Select from preset sound settings (Personal, Theater, Music, Voice, Standard)
to match the type of show you are watching. (Select Personal mode to recall
your customed settings on bass and treble.)
17
PLV1615CS1- E2-23 JENSEN-DC.pmd
17
06/08/2007, 17:57
TV SETUP
TV MENU (For TV Mode Only)
1. Press the MENU button.
2. Use the
ENTER or button to go into the TV settings.
3. Use the or button to select the options
or
button to select TV. Press the
Video
Audio
Tuner Mode
Auto Scan
Cable
Auto Scan Add CH
Channel Skip
MTS
TV
(Tuner Mode, Auto Scan, Add Channel, Channel
Skip, MTS or Audio Language). Adjust them using
Stereo
Setup
Audio Language
English
the
or
button (The screen will change to
Parental
your desired setting); or press the ENTER or
button to go into the detailed settings.
4. Press the EXIT button to return to the previous
menu.
TV
Select EXIT Exit
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
•Tuner mode :
Antenna (over-the-air broadcasts) or Cable (cable/satellite broadcasts)
mode are available.
•Auto Scan Add CH: Search for more usable stations and add them in memory. (The stations
stored before are still kept.)
•Add Channel:
•Channel Skip:
•MTS:
Search for more usable stations and add them in memory.
Skip weak channels and the channels you don’t like.
Select Stereo / SAP (Secondary Audio Program) / Mono.
Select from English / Spanish / French. (Available for digital channels
if multiple audio langrages are broadcasted.)
•Audio Language:
Note: The SAP (Secondary Audio Programs) feature allows a TV station to broadcast other
information, which could be audio in another language.
Channel Skip Setting:
1. Use the
or
button to select a
button to select the
Video
Audio
2
Analog
Analog
Analog
Analog
Digital
channel. (Press the
last channel of the page, press again to
the next page. Press the button to select
the first channel of the page, press again
to the previous page.)
3
4
5
TV
5-1
6
KPIX-DT
Setup
Analog
Analog
Analog
Analog
Analog
7
Parental
2. Press the ENTER button to shift between
skip or not skip the channel. (“ ” appears
in the square means skip the selected
channel. The channel will not appear
when you press the CH+/CH– Button.)
8
9
10
Channel Skip
Select EXIT Return
SETUP MENU
1. Press the MENU button.
2. Use the
settings.
or
button to select Setup. Press the ENTER or
button to go into the Setup
3. Use the
or
button to select the options (OSD Language, Time Setup, Caption or
Restore setting). Adjust them using the
or
button (The screen will change to your
desired setting); or press the ENTER or
button to go into the detailed settings.
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
18
PLV1615CS1- E2-23 JENSEN-DC.pmd
18
06/08/2007, 17:57
TV SETUP
TV MODE
AV / YUV MODE
Video
Audio
OSD Language
English
Video
OSD Language
Time Setup
Caption
English
Time Setup
Caption
Audio
Setup
Parental
Restore setting
Restore setting
TV
Setup
Parental
Setup
Select EXIT Exit
Setup
Select EXIT Exit
PC MODE
Video
OSD Language
Time Setup
English
• OSD Language : Select from English /
Español / Français.
Audio
Setup
Parental
Restore setting
Setup
Select EXIT Exit
Time Setup Setting:
Video
Audio
Time Update
Date
Off
Video
Audio
Time Zone
Time
EasternTime
Off
2000/01/01
07:42:49
Time
SleepTimer
TV
TV
Timer
Off
Setup
Setup
Power OnTime
Power OffTime
00:00:00
00:00:00
Parental
Parental
Time
Time Setup
Select EXIT Return
Select EXIT Return
• Time Zone
: Select the time zone from Eastern Time / Indiana / Central Time / Mountain
Time / Arizona / Pacific Time / Aalaska / Hawaii.
• Sleep Timer
: Select the time to turn the unit to Standby mode automatically: Off -> 5
Minutes -> 10 Minutes -> 15 Minutes -> 30 Minutes -> 60 Minutes -> 90
Minutes -> 120 Minutes -> Off.
When you set the ‘Time’, the option will be shown:
• Time Update
: Select On/Off to activate the following manual settings; Select Auto to
synchronize time with the digital TV channel signal.
: Press the or button to locate the position, and press the number
buttons to input date.
: Press the or button to locate the position, and press the number
• Date
• Time
buttons to input time.
: Select On to activate automatically power on/off.
• Timer
• Power On Time : Press the
or
button to locate the position, and press the number
buttons to input power on time.
• Power Off Time : Press the
or
button to locate the position, and press the number
buttons to input power off time.
19
PLV1615CS1- E2-23 JENSEN-DC.pmd
19
06/08/2007, 17:57
TV SETUP
Caption Setting:
Video
Audio
Caption Style
Font Size
As Broadcaster
Small
Video
Audio
Analog Closed Caption
Off
Off
Digital Closed Caption
Digital Caption Style
Font Style
Style 1
Font Color
Green
TV
TV
Font Opacity
Background Color
Background Opacity
Window Color
Window Opacity
Solid
Setup
Setup
Black
Translucent
White
Parental
Parental
Transparent
Digital Caption Style
Caption
Select EXIT Return
Select EXIT Return
• Analog Closed Caption : Select the analog closed caption or turn it off.
• Digital Closed Caption : Select the digital closed caption or turn it off.
• Digital Caption Style : Select As Broadcaster to use the default digital caption style of
the broadcaster. Select Custom to activate the caption style items
and set you prefered detailed settings.
Note: This function only works on ATSC programs broadcast with captions.
Restore Setting:
If you reset the TV to the factory settings, all your present settings on Video & Audio will be
erased and replaced by the factory’s default settings. However, picture settings in PC mode and
Parental settings will not be erased.
PARENTAL MENU
Password
1. Press the MENU button.
2. Use the
or
button to select Parental. Press the ENTER or
button to confirm. The
menu locked screen will be displayed.
3. Enter a 4-digit password. Once entered, the screen will enter the Parental menu. The preset
password is 0000.
You can edit the parental control level or change the password. See Parental Control
Settings on the next page.
TV MODE
AV / YUV / PC MODE
Video
Audio
Password
Video
Audio
Setup
Password
TV
Setup
Parental
Parental
Parental
Select EXIT Exit
Parental
Select EXIT Exit
If you forget the password,
enter " 8888 " to unlock parental control.
20
PLV1615CS1- E2-23 JENSEN-DC.pmd
20
06/08/2007, 17:57
TV SETUP
Parental Control Setting:
4. Use the
go into the detailed settings.
5. Use the and buttons to move among the rating levels. Press the ENTER button to
or
button to select various Parental settings. Press the ENTER or
button to
,
,
change the mode between Blocked and Allowed.
6. Press the EXIT button to return to the previous menu.
7. Repeat steps 4 - 6 to adjust other options.
8. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
Video
Rating Enable
On
Video
Program Block
Change Password
Clean All
U.S.TV Ratings
Audio
Setup
Parental
Audio
Setup
Parental
U.S. Movie Ratings
Canadian English Ratings
Canadian French Ratings
OpenV-Chip
Program Block
Select EXIT Return
Parental
ENTER Enter
Select EXIT Return
• Rating Enable : Select On to edit the following parental items. Select Off to disable parental
control.
• OpenV-Chip : Read the ratings from ATSC TV programs if there is rating information
broadcasted, and denies the channel when its rating is higher than the
ratings you pre-set.
TV-Y
TV-Y7 : Recommended for all children age 7 and above.
TV-G : General Audience.
TV-PG : Parental Guidance Suggested.
TV-14 : Parental Strongly Cautioned.
TV-MA : Mature Audience Only.
: Recommended for all children.
U.S.
TV
Ratings
G
PG
: GENERAL AUDIENCES, Suitable for all ages.
: PARENTAL GUIDANCE SUGGESTED - Some material may not be
suitable for children.
U.S.
PG-13 : PARENTS STRONGLY CAUTIONED
inappropriate for children under 13.
-
Some material may be
Movie
Ratings
R
: RESTRICTED, Under 17 requires accompanying parent or adult
guardian for viewing in movie theaters.
NC-17 : No one 17 or under admitted in movie theaters,
X
: Adults Only.
C
C8+
G
: Children.
: Recommended for children age 8 and older.
: GENERAL AUDIENCES, Suitable for all ages.
: PARENTAL GUIDANCE SUGGESTED - Some material may not be
suitable for children.
Canadian
English
Ratings
PG
14+
18+
: Viewers 14 years and older.
: Adult Programming.
G
: GENERAL AUDIENCES, Suitable for all ages.
Canadian
French
Ratings
8 ans+ : Not recommended for young children.
13 ans+ : Not suitable for children under the age of 13.
16 ans+ : Not suitable for children under the age of 16.
18 ans+ : Adult Programming.
21
PLV1615CS1- E2-23 JENSEN-DC.pmd
21
06/08/2007, 17:57
TROUBLE SHOOTING GUIDE
SYMPTOM
CAUSE (AND REMEDY)
• Check that the AC adapter/car plug is connected.
• Turn on the unit.
No power.
• Remove any obstacles between the remote and the unit.
• Use the remote near the unit.
The remote does not
function.
• Point the remote at the remote sensor on the unit.
• Replace the battery in the remote with a new one.
Bad Picture (snow,
• Check the location of the antenna and adjust it if necessary.
• Make sure the antenna cable is connected firmly.
• Make sure all input cables are firmly connected.
multiple
images,
distortion, blurry)
No sound.
• Increase the volume.
• Check whether the mute function has been activated on
the Remote Control.
Black
picture.
and
white
• Check the Picture setting within the Setup menu.
• Check to make sure the program you are watching is
broadcast in Color and not Black & White.
No picture or sound.
• Make sure the unit is plugged in and turned on.
• Make sure that the TV mode is selected.
• Try a new channel to check for possible station trouble.
• Make sure the antenna is connected properly.
• Increase the volume.
• Make sure the antenna or audio/video source device is
working properly.
• Make sure all cables are connected firmly.
• Check for local interference.
Colored patches of
picture.
• Make sure there are no unshielded electrical devices
nearby that are causing interference.
• Turn the TV off for 30 minutes, then try it again.
22
PLV1615CS1- E2-23 JENSEN-DC.pmd
22
06/08/2007, 17:57
Unit : INCH
3 ½
15 5/8
6 5/8
7 1/2
10 1/2
23
PLV1615CS1- E2-23 JENSEN-DC.pmd
23
06/08/2007, 17:57
|