Ingersoll Rand Water Pump 6661HX XXX C User Manual

OPERATOR’S MANUAL  
6661HX-XXX-C  
RELEASED: 12-18-06  
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE  
REVISED:  
(REV. 04)  
5-20-10  
1" DIAPHRAGM PUMP  
CSA CERTIFIED, 1:1 RATIO, METALLIC  
INTENDED FOR USE WITH SWEET NATURAL GAS  
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,  
OPERATING OR SERVICING THIS EQUIPMENT.  
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.  
SERVICE KITS  
Refer to Model Description Chart to match the pump mate-  
rial options.  
637118-C for gas section repair (see page 6).  
637119-C9-C for fluid section repair (see page 4).  
PUMP DATA  
Models. . . . . . . . . . . . . see Model Description Chart for “-XXX”  
Pump Type. . . . . . . . . Gas Operated Double Diaphragm  
Material. . . . . . . . . . . . see Model Description Chart  
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 lbs (8.62 kgs)  
Maximum Gas Inlet Pressure . . . . . . . 120 p.s.i.g. (8.3 bar)  
Maximum Material Inlet Pressure. . . 10 p.s.i.g. (0.69 bar)  
Maximum Outlet Pressure . . . . . . . . . . 120 p.s.i.g. (8.3 bar)  
(flooded inlet)  
Maximum Flow Rate  
. . . 35 g.p.m. (133 l.p.m.)  
Figure 1  
Displacement / Cycle @ 100 p.s.i.g. . 0.156 gal. (0.59 lit.)  
Maximum Particle Size . . . . . . . . . . . . . 1/8dia. (3.2 mm)  
Maximum Temperature Limits . . . 32° to 125° F (0° to 52° C)  
Dimensional Data. . . . . . . . . . . . . . . . . . . see page 8  
MODEL DESCRIPTION CHART  
Noise Level @ 70 p.s.i., 60 c.p.m.. . . . . . 64.5 db(A)  
c
6661 H 0 - 1 C 9 - C  
The pump sound pressure levels published here have been updated to  
an Equivalent Continuous Sound Level (LAeq) to meet the intent of ANSI  
S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.  
c
Center Section Material, Fluid Connection  
H - Aluminum, 1 - 11-1/2 N.P.T.F. - 1  
Fluid Cap / Manifold Material, Hardware  
0 - Aluminum, Carbon Steel  
Seat Material  
1 - Aluminum  
Ball Material  
C - Hytrel®  
Diaphragm Material  
9 - Hytrel  
Fluid Section Service Kit Selection  
6661H0 - 1 X X - C  
637119 - X X - C  
EXAMPLE: Model #6661H0-1C9-C  
Fluid Section Service Kit # 637119-C9-C  
Ball  
Diaphragm  
INGERSOLL RAND COMPANY LTD  
209 NORTH MAIN STREET – BRYAN, OHIO 43506  
© 2010  
CCN 15276603  
(800) 276-4658 FAX (800) 266-7016  
y
 
GENERAL DESCRIPTION  
MAINTENANCE  
The ARO natural gas powered diaphragm pump offers high  
volume delivery even at low gas pressure. Natural gas pow-  
ered diaphragm pumps move fluids such as crude oil, salt  
water, drilling mud, lubrication oils, glycol, caustic liquids and  
acids. ARO pumps feature stall resistant design, modular gas  
motor / fluid sections.  
Gas operated double diaphragm pumps utilize a pressure  
differential in the gas chambers to alternately create suc-  
tion and a positive fluid pressure in the fluid chambers, ball  
checks insure a positive flow of fluid.  
Pump cycling will begin as gas pressure is applied and it will  
continue to pump and keep up with the demand. It will build  
and maintain line pressure and will stop cycling once maxi-  
mum line pressure is reached (dispensing device closed) and  
will resume pumping as needed.  
Certain ARO “Smart Parts” are indicated which should be  
available for fast repair and reduction of down time.  
Provide a clean work surface to protect sensitive internal  
moving parts from contamination from dirt and foreign  
matter during service disassembly and reassembly.  
Keep good records of service activity and include the  
pump in preventive maintenance program.  
Service kits are available to service two separate dia-  
phragm pump functions: 1. GAS SECTION, 2. FLUID SEC-  
TION. The Fluid Section is divided further to match typical  
active Material Options.  
y
y
y
y
Before disassembling, empty captured material in the  
outlet manifold by turning the pump upside down to  
drain material from the pump.  
y
FLUID SECTION DISASSEMBLY  
1. Remove top manifold(s).  
2. Remove (22) balls, (19) “Orings and (21) seats.  
3. Remove (15) fluid caps.  
4. Remove (14) screws, (6) washers, (7) diaphragms and (5)  
washers.  
GAS AND LUBE REQUIREMENTS  
WARNING EXCESSIVE GAS PRESSURE. Can cause pump  
damage, personal injury or property damage.  
A filter capable of filtering out particles larger than 50  
microns should be used on the gas supply. There is no lu-  
brication required other than the “O” ring lubricant which  
is applied during assembly or repair.  
y
y
5. Remove (3) “O” rings. NOTE: Do not scratch or mar the  
surface of (1) diaphragm rod.  
If lubricated gas is present, make sure that it is compat-  
ible with the “O” rings and seals in the gas motor section  
of the pump.  
FLUID SECTION REASSEMBLY  
Reassemble in reverse order.  
Clean and inspect all parts. Replace worn or damaged  
parts with new parts as required.  
y
y
OPERATING INSTRUCTIONS  
Always flush the pump with a solvent compatible with  
the material being pumped if the material being pumped  
is subject to “setting up” when not in use for a period of  
time.  
Disconnect the gas supply from the pump if it is to be  
inactive for a few hours.  
The outlet material volume is governed not only by the  
gas supply, but also by the material supply available at  
the inlet. The material supply tubing should not be too  
small or restrictive. Be sure not to use hose which might  
collapse.  
Lubricate (1) diaphragm rod and (2) “O” ring with Key-  
Lube grease.  
Use ARO pn 98930-T bullet (installation tool) to aid in in-  
stallation of (2) “Oring on (1) diaphragm rod.  
Be certain (7) diaphragms align properly with (15) fluid  
caps before making final torque adjustments on bolt and  
nuts to avoid twisting the diaphragm.  
y
y
y
y
y
y
Re-check torque settings after pump has been re-started  
and run a while.  
y
When the diaphragm pump is used in a forced-feed  
(flooded inlet) situation, it is recommended that a “check  
valvebe installed at the gas inlet.  
Secure the diaphragm pump legs to a suitable surface to  
insure against damage by vibration.  
y
y
Loctite® is a registered trademark of Henkel Loctite Corporation 271™, 262™, 572™ and 577™ are trademarks of Henkel Loctite Corporation  
y
y
y
Hytrel® and Viton® are registered trademarks of the DuPont Company ARO® is a registered trademark of Ingersoll-Rand Company  
y
y
y
6661HX-XXX-C (en)  
Page 3 of 8  
 
PARTS LIST / 6661HX-XXX-C FLUID SECTION  
637119-C9-C fluid section service kits include: Balls (item 22), diaphragms (item 7) plus items 2, 3, 19 and 93706-1 Key-Lube  
grease (page 6).  

PARTS LIST  
(size)  
(size)  
Item Description  
Qty Part No.  
(1) 98724-1  
(1) Y330-113  
(4) Y328-14  
(2) 93441-2  
(2) 93441-2  
(2) 90533-9  
(2) 93189-1  
(2) Y5-85-T  
(2) 94945  
[Mtl]  
[C]  
Item Description  
16 Manifold  
Qty Part No.  
(2) 92001  
[Mtl]  
[A]  
[V]  
[A]  
[H]  
[C]  
[C]  
1
2
3
5
6
7
9
Rod  
“O” Ring  
“O” Ring  


(3/32” x 3/4” o.d.)  
(1/16” x 5/8” o.d.)  
(3/32” x 1-9/16” o.d.)  
[B]  
[T]  
19 “O” Ring  
21 Seat  
(4) Y327-126  
(4) 92008-1  
(4) 90532-C  
(8) Y6-55-C  
(16) Y12-5-C  
(1) 93004  

(3-5/8” o.d.)  
(1” diameter)  
Washer - Air side  
Washer - Fluid side  
Diaphragm  
[C]  
[C]  
[H]  
[SS]  
[SS]  
[A]  
22 Ball  
26 Bolt  
29 Nut  
43 Ground Lug  
57 Ground Kit Assembly  

(5/16” - 18 x 1”)  
(5/16" - 18)  

(0.505” i.d.)  
(see page 7)  
Washer  
[Co]  
- - -  
(1/2” - 20 x 1”)  
(not shown)  
14 Screw  
15 Fluid Cap  
(1) 66885-1  
MATERIAL CODE  
“Smart Parts, keep these items on hand in addition to the service kit for fast repair and reduction of down time.  
[A] = Aluminum  
[B] = Nitrile  
[C] = Carbon Steel  
[Co] = Copper  
[H] = Hytrel  
[SS] = Stainless Steel  
[T] = PTFE  
[V] = Viton®  
Page 4 of 8  
6661HX-XXX-C (en)  
 
PARTS LIST / 6661HX-XXX-C FLUID SECTION  
3
2
1
4
FOR THE GAS MO-  
TOR SECTION, SEE  
PAGES 6 & 7.  
5
7
8
6
26  
16  
(
Torque Sequence  
2
1
3
5
7
6
3
9
14  
( ‹  
œ
œ
œ
œ
22  
19  
21  
œ
15  
29  
(
œ
22  
21  
19  
16  
26  
(
Figure 2  
TORQUE REQUIREMENTS  
)
(
NOTE: DO NOT OVERTIGHTEN FASTENERS.  
(14) Bolt, 25 - 30 ft. lbs (33.9 - 40.7 Nm).  
(26) Bolt, 120 - 140 in. lbs (13.6 - 15.8 Nm).  
(29) Nut, 120 - 140 in. lbs (13.6 - 15.8 Nm).  
Gas side  
Fluid side  
LUBRICATION / SEALANTS  
Apply Loctite® 271™ to threads.  
œ
Apply Key-Lube grease (93706-1) to all “O” rings, “U” cups and mating  
parts.  
Cross section view of diaphragm.  
6661HX-XXX-C (en)  
NOTICE: Radius edge of parts (5 and 6) is against diaphragm.  
Page 5 of 8  
 
PARTS LIST / 6661HX-XXX-C GAS MOTOR SECTION  
Indicates parts included in 637118-C gas section repair kit.  
9
GAS MOTOR PARTS LIST  
(size)  
(size)  
Item Description  
101 Motor Body  
(Qty) Part No.  
(1) 94743  
(2) Y325-20  
(1) 94527  
(2) Y145-25  
(8) 93860  
(2) 92003  
(1) 92878  
(1) 92011  
(1) Y186-51  
(1) 92005  
(5) 92877  
(5) Y325-214  
(6) Y325-126  
(4) 92876  
(1) 92006  
[Mtl]  
[A]  
Item Description  
(Qty) Part No.  
(1) 92004  
(1) 93309-1  
(4) 93075  
(3) 115959  
(2) 98723-1  
(2) 94820  
(4) Y154-41  
(16) 92866  
(1) Y227-2-L  
[Mtl]  
[B/Ny]  
[C]  
[U]  
[Z]  
[Bz]  
[U]  
[C]  
[C]  
[C]  
117 Gasket  
118 Pilot Rod  
119 “O” Ring  
120 Spacer  
121 Sleeve Bushing  
122 “O” Ring  
9
(1/16” x 1” o.d.)  
102 “O” Ring  
103 Sleeve  
[B]  
[D]  
[C]  
[C]  
[C]  
[B/Ny]  
[D]  
[B]  
[A]  
[Z]  
9
(1/8” x 3/4” o.d.)  
9
(0.925 i.d.)  
104 Retaining Ring  
9
(1/4” - 20 x 5/8”)  
105 Screw  
107 Leg  
(3/32” x 9/16” o.d.)  
9
9
(with notch)  
(#8 - 32 x 3/8”)  
108 Gasket  
109 Piston  
110 “U” Cup  
111 Spool  
112 Washer  
113 “O” Ring  
114 “O” Ring  
115 Spacer  
116 Spacer  
123 Screw  
9
(5/16” - 18 x 1-3/4”)  
124 Stud  
(3/16” x 1-3/8” o.d.)  
(1/8 - 27 N.P.T. x 1/4”)  
(1/4”)  
128 Pipe Plug  
133 Lockwasher  
197 Button Head Screw  
198 Button Head Screw  
9
(1) Y14-416-T [SS]  
(2) 94987  
(1) 94987-1  
(1.557” o.d.)  
(1/4” - 20 x 1/4”)  
(1/4” - 20 x 3/8”)  
[SS]  
[SS]  
(1/8” x 1-1/4” o.d.)  
(3/32” x 1-9/16” o.d.)  
[B]  
[B]  
[Z]  
[Z]  
9
9
Key-Lube “O” Ring Lubricant  
Key-Lube, 10 Pack  
(1) 93706-1  
637175  
9
“Smart Parts, keep these items on hand in addition to the service kit for fast repair and reduction of down time.  
MATERIAL CODE  
PILOT VALVE REASSEMBLY  
[A] = Aluminum  
[B] = Nitrile  
[Bz] = Bronze  
[C] = Carbon Steel  
[D] = Acetal  
[Ny] = Nylon  
[SS] = Stainless Steel  
[U] = Polyurethane  
[Z] = Zinc  
1. Replace two (102) “Orings, if worn or damaged, and rein-  
stall (103) sleeve.  
2. Install one of the (121) sleeve bushings, (119) “O” rings,  
(120) spacers and the remaining (121) bushing.  
3. Carefully push (118) pilot rod into bushing etc. and retain  
on each end with the two (122) “O” rings. Retain with  
(123) screws.  
GAS MOTOR SECTION SERVICE  
Service is divided into two parts - 1. Pilot Valve, 2. Major  
Valve.  
4. Replace (104) retaining rings.  
GENERAL SERVICE NOTES:  
Gas Motor Section service is continued from Fluid Section  
repair.  
y
MAJOR VALVE DISASSEMBLY  
Inspect and replace old parts with new parts as neces-  
sary. Look for deep scratches on metallic surfaces, and  
nicks or cuts in “Orings.  
Take precautions to prevent cutting “O” rings upon instal-  
lation.  
y
1. Remove (107) legs and (108 and 117) gaskets.  
2. On the side opposite the air inlet, push on the inner di-  
ameter of (111) spool. This will force the (109) piston out.  
Continue pushing the (111) spool and remove. Check for  
scratches and gouges.  
3. Reach into the gas section (exhaust side) and remove  
(116) spacer, (115) spacers, (113) “O” rings, (114) “O” rings,  
(112) washers, etc. Check for damaged “Orings.  
y
Lubricate “Orings with Key-Lube grease.  
Do not over-tighten fasteners. Refer to torque specifica-  
tion block on view.  
y
y
Re-torque fasteners following restart.  
y
MAJOR VALVE REASSEMBLY  
PILOT VALVE DISASSEMBLY  
1. Remove (104) retaining ring.  
2. Remove (123) screws and (122) “Orings.  
3. Remove (118) piston rod, (121) sleeve bushing, (119) “O”  
rings and (120) spacers from the (101) motor body.  
4. Remove (103) sleeve and (102) “Orings.  
1. Replace (112) washer, (114) “O” ring and (113) “O” ring  
onto (115) spacer and insert etc. NOTE: Be careful to ori-  
ent spacer legs away from blocking internal ports.  
2. Lubricate and carefully insert (111) spool.  
3. Install (117) gasket and (107) leg.  
4. Lubricate and install (110) packing cup and insert (109)  
piston into (air inlet side) cavity, the (110) packing cup  
lips should point outward.  
5. Install (108) gasket and replace (107) leg.  
Page 6 of 8  
6661HX-XXX-C (en)  
 
PARTS LIST / 6661HX-XXX-C GAS MOTOR SECTION  
IMPORTANT  
BE CERTAIN TO ORIENT (115) SPACER LEGS  
AWAY FROM BLOCKING INTERNAL PORTS  
WHEN REASSEMBLING GAS SECTION.  
117  
111  
œ
115  
116  
114  
œ
105  
107  
(
113  
œ
112  
MAJOR VALVE  
See cross section detail, figure 4.  
128  
101  
197  
Figure 3  

104  
123  
121  
43  
124  
197  

œ
102  
103  
104  
œ
œ
133  
198  

105  
107  
)
119  
109  
110  
121  
123  
118  
122  
œ
108  
œ
œ
120  
PILOT VALVE  
MAJOR VALVE CROSS SECTION DETAIL  
109 110 112 114 113 115 111  
116  
œ
œ
œ
œ
) TORQUE REQUIREMENTS (  
NOTE: DO NOT OVERTIGHTEN FASTENERS.  
(105) Torque to 40 - 50 in. lbs (4.5 - 5.6 Nm).  
LUBRICATION / SEALANTS  
œ
Apply Key-Lube grease to all “O” rings, “U”  
cups and mating parts.  
Apply Loctite 262™ to threads.  
Apply Loctite 572™ to threads.  
Figure 4  

Apply Loctite 577™ to threads.  
6661HX-XXX-C (en)  
Page 7 of 8  
 
TROUBLE SHOOTING  
Product discharged from exhaust outlet.  
Low output volume, erratic flow or no flow.  
Check for diaphragm rupture.  
Check gas supply.  
y
y
y
y
y
y
Check tightness of (14) diaphragm screw.  
Check for plugged outlet hose.  
Check for kinked (restrictive) outlet material hose.  
Check for kinked (restrictive) or collapsed inlet material  
hose.  
Gas bubbles in product discharge.  
Check connections of suction plumbing.  
Check “Orings between intake manifold and fluid caps.  
Check tightness of (14) diaphragm screw.  
y
y
y
Check for pump cavitation - suction pipe should be sized  
at least as large as the inlet thread diameter of the pump  
for proper flow if high viscosity fluids are being pumped.  
Suction hose must be a non-collapsing type, capable of  
pulling a high vacuum.  
y
Check all joints on the intake manifolds and suction con-  
nections. These must be gas tight.  
Inspect the pump for solid objects lodged in the dia-  
phragm chamber or the seat area.  
y
y
DIMENSIONAL DATA  
Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).  
L (outlet)  
Gas inlet 1/4 - 18 N.P.T.F. - 1  
A
E
B
G
F
D
H
K
J
C
(inlet) L  
DIMENSIONS  
Figure 5  
A - 8-1/2(215.9 mm)  
E - 8” (203.2 mm)  
H - 6-1/4” (158.8 mm)  
J - 7-5/16" (185.7 mm)  
K - 7/16” (11.1 mm)  
B - 11-9/16(293.7 mm) F - 6-1/2” (165.1 mm)  
C - 4(101.6 mm)  
D - 1-1/4(31.8 mm)  
G - 12-1/2” (317.5 mm)  
Pump Model  
6661H0-1C9-C  
LMaterial Inlet / Outlet  
1 - 11-1/2 N.P.T.F. - 1  
PN 97999-1236  
Page 8 of 8  
6661HX-XXX-C (en)  
 

Ingersoll Rand Saw 66651 B User Manual
Insignia Portable DVD Player NS 7DPDVD User Manual
Jabra Refrigerator JX10 User Manual
Jensen Car Stereo System MP8610BT User Manual
John Lewis Dishwasher JLDWW 905 User Manual
JVC Universal Remote KD G401 User Manual
Kenmore Refrigerator 7957977 User Manual
Kenwood GPS Receiver DNX6490BT User Manual
Kenwood Marine Radio TK 5220 User Manual
KitchenAid Clothes Dryer KEYE850V User Manual