Ingersoll Rand Cordless Sander 16574014 User Manual

16574014

Edition 1

June 2006

Air Grinder, Die Grinders and

Sanders

CA Angle Series

Parts Information

Save These Instructions

CA Angle Air Grinder, Die Grinder and Sander Parts List

Item

Part Description

Part Number Item

Part Description

Part

Number

Common parts for ALL CA Grinders

Inlet Assembly

22 Angle Housing Assembly

LA1-A550S

LA1-46

LG1-A465A

R1602-61

85H-167

LG1-K300

LG1-300A

LG1-303

AG210-302

7L-51

Clamp Spacer

Clamp Nut

Inlet Screen

LG1-27

•

Inlet Seal

Grease Fitting

Upper Arbor Bearing

Wick

D0F9-879

AG210-693

Throttle Valve Cartridge Kit

Throttle Valve Cartridge Case

Throttle Valve Seat

Throttle Valve

for CA120

LA1-560

LA1-561

for CA200

Throttle Valve Spring

Throttle Valve Spring Seat

Motor Housing

28 Bevel Gear Nut

29 Lower Arbor Bearing

30 Arbor Bearing Cap

31 Arbor

AG210-578A

AG210-24

AG210-531

LG1-592

LG1-40

Throttle Lever

LG1-273

LG1-A400

6A Locking Throttle Lever Assembly

(for models ending in L, C, ML or MC)

for all models ending in

G4, G4C or G4L

AG210-4-G4

AG210-4-W2

Lever Lock

LG1-402

LG1-405

5UT-757

61H-120

LG1-191

DG230-22

DG20-278

LG1-118

for all models ending in

S4, S4C or S4L

Lock Spring

Lock Pin

for all models ending in

P63, P63C or P63L

LA1-6

Throttle Lever Pin

Throttle Valve Plunger

Rear Rotor Bearing

H63, H63C or H63L

LA1-103-1

Warning Label

for models ending in P63-EU

•

10 Rear Rotor Bearing Spacer (2)

11 Rear Rotor Bearing Retainer

12 Rotor

EU-63--99

EU-99

for all other models ending in-EU

for all other models

LG1-99

for CA120 (5 vane slots)

for CA200 (3 vane slots)

13 Vane Packet (set of 5 Vanes)

14 Front End Plate

LG1-53-5

LG1-53-3

LG1-42-5

LG1-11

Nameplate

for CA120 models ending in-EU

for all other CA120 models

for CA200 models ending in-EU

for all other CA200 models

LA112-EU-301

LA112-301

•

LA120-EU-301

LA120-301

15 Front End Plate Spacer

16 Front Seal Cup

DG10-65-5

LG1-32

Additional parts for all collet

models

17 Front Rotor Bearing

18 Flow Ring

LG1-24

32 Collet

for CA120 (12000 rpm) (brown)

for CA200 (20000 rpm) (red)

19 High Profile Flange

LG1-103-1

LG1-103-3

LG1-23

for models ending in-EU

DG110-700-

6mm

for all other models

DG110-700-

19A Low Profile Concentric Flange

(for all models ending in C)

LG1R-23

33 Nosepiece

34 Collet Nut

AG210-698A

AG210-699A

20 Flange Clamp

LG1-29

21 Bevel Pinion and Bevel Gear

(sold only as a matched set)

for CA120

for CA200

LA1-A552-2.0S

LA1-A552-1.5A

* Not illustrated.

• To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one

(pair or set) of each part indicated by a bullet (•) for every four tools in service.

¤ The LA1-A550S Angle Housing Assembly is furnished with two Wicks. Use Wick (LA1-561) with the notch on CA200 models.

WARNING

# Always install a Locking Throttle Lever Assembly (6A) on a tool with a Low Profile Concentric Flange (19A). Do not

equip a tool with a standard non-locking Throttle Lever (6) and Low Profile Concentric Flange. This can allow the tool to

continue to run if dropped or set down.

16574014_ed1

Item

Part Description

Part Number Item

Part Description

Part

Number

Additional parts for all

models ending in P63 or H63

Variable Speed Control Assembly

(with piped away exhaust)

LG1-A1015

35 Wheel Guard

AG20-106-3

R2-320

Piped Away Exhaust Kit

Exhaust Hose Adapter

Exhaust Hose Retainer

Exhaust Hose

LG1-K284

LG1-284

LG1-67

36 Guard Lock Washer (3)

37 Guard Mounting Screws (3)

38 Wheel Flange (for P63)

39 Flange Nut

LA1-667

R0A2D61-337

3RL-284

LG1-K1

LG1-K2

LG1-K3

Bur Kit

for P63

AG21-337A-3

LA1-388

2” Abrasive Pad Kit

for H63

3” Abrasive Pad Kit

(for CA120 models only)

40 Flange Spacer (for P63)

41 Guard Adapter Assembly

LA2-111

LA1-A710

804-634

Shroud Kit (for collet models only)

No. 10 Oil (4 oz. bottle)

LA1-K980

10Z4

Guard Pinch Bolt

Additional parts for

all models ending in S4

No. 63 Oil (4 oz. bottle)

63Z4

No. 67 Grease (1 lb. can)

No. 77 Grease (1 lb. can)

Shroud Kit (for non-collet models)

67-1LB

77-1LB

LA1-K975

43 Sanding Pad

(standard on models ending

in S4M, S4MC or S4ML; optional on

models ending in S4, S4C or S4L)

for CA120 (3” diameter)

for CA200 (2” diameter)

3-PAD

2-PAD

Accessories for CA models

44 Collet Body Wrench/Collet Nut Wrench

(7/16” x 11/16” ) (included with all

DG20-69A

models ending in G4, G4C or G4L)

46 Arbor Bearing Cap Wrench

for models ending in S4, S4C

or S4L

AG210-29

for models ending in H63

LA1-29

47 Clamp Nut Wrench

(included with all models)

LA2-253

48 Arbor Wrench (3/16” hex)

(included with all

AG220-340

D32-26

models ending in P63, P63C or P63L)

49 Wheel Nut Wrench (included with all

models ending in P63, P63C or P63L)

* Not illustrated.

Ø When ordering a Piped-Away Exhaust Kit, make certain the wrench hex on the Inlet Assembly of your tool is threaded. If it is

NOT threaded, order a new Inlet Assembly (Part No. LG1-A465A).

+ Standard equipment on models ending in M, MC or ML and ALL Front Exhaust models; optional equipment on all other models.

Parts and Maintenance

When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by

material so that they can be recycled.

Tool repair and maintenance should only be carried out by an authorized Service Center.

Refer all communications to the nearest Ingersoll Rand Office or Distributor.